# OSSO reflow process (TEST BASELINE, 2026-10-28, v6)
**Status: test baseline. All values are subject to the coupon tests**, which set the final values. Replaces project/docs/process_single_step_reflow.md (single-step is deprecated).
Drawing: drawings/2026_10_28_two_step_reflow_pad_guidance_v6.png (supersedes v2-v5). Table and script: project/runs/q_run_20261028/item5_reflow/ball_count_table_v5.json, calc_v5.py (default D = 0.25; per-part tunable `BALLS_OVERRIDE`).

> **RULE: one ball size for every part: Ø0.25 SAC305 (replaces Ø0.30). One ball size per job; never switch sizes mid-job. Volume is tuned by ball COUNT only.**

**Solder unit:** each Ø0.25 ball is a fixed, precise volume: π/6 x 0.25³ = **0.00818 mm³**. Volume reference (100 %) = pad area x 0.06 mm (≈ a 0.12 mm stencil print at ~50 % metal).

## Step 1: minimal tin (10-20 µm)
Goal: wet the pad and give a flat, consistent surface for tacky-flux placement; NOT to supply joint volume.
1. Flux the pads.
2. **Flux-loaded wick wipe:** one pass of flux-loaded solder wick under the iron over each pad. Self-limiting: thin (about 10-20 µm), flat, the same on every pad, no crown.
3. IPA clean. **Check:** tin peak ≤ 25 µm, pads of one part within 10 µm. No oven reflow in step 1.

## Step 2: pick-and-place with tacky flux
ONE tacky flux patch per terminal, covering the terminal landing and the ball spots on the toe (and heel). Place the parts.

## Step 3: Ø0.25 balls AFTER placement, then ONE reflow
- Place the balls (count from the table) outside the part body: at the outer toe touching the terminal end (gap ~0.02, row 0), further rows directly behind it, and at the heel on gull-wing leads where the heel has room (≥ 0.35 mm exposed). Same count and layout on both terminals.
- The solder goes into the visible fillet, not under the part.
- Reflow once (bed soak profile, process_v3 step 10). IPA clean, inspect, test.

## Baseline table (per terminal, Ø0.25)
% = minimal tin + balls vs the 100 % reference, at 10 / 15 / 20 µm tin (15 µm nominal). Target 100-130 %.

| Part | balls (baseline, tunable) | layout | % at 10 / 15 / 20 µm | % at 15 µm with -1 / +1 ball | toe exposed / needed → extension (mm) | ball to next pad (mm) |
|---|---|---|---|---|---|---|
| 0402 (0.50x0.60) | **2** | toe row0: 2 | 108 / 116 / 124 | 70 / 161 | 0.33 / 0.35 → +0.02 | layout: keep >= 0.20 pad-to-pad |
| 0603 (0.80x0.90) | **4** | toe row0: 3; toe row1: 1 | 92 / 101 / 109 | 82 / 120 | 0.495 / 0.6 → +0.105 | layout: keep >= 0.20 pad-to-pad |
| 0805 (1.0x1.3) | **8** | toe row0: 4; toe row1: 4 | 101 / 109 / 117 | 98 / 119 | 0.715 / 0.6 → none | layout: keep >= 0.20 pad-to-pad |
| 1206 (1.6x1.6) | **14** | toe row0: 6; toe row1: 6; toe row2: 2 | 91 / 100 / 108 | 94 / 105 | 0.88 / 0.85 → none | layout: keep >= 0.20 pad-to-pad |
| SOT-23 lead (0.6x1.0) | **4** | toe row0: 2; toe row1: 2 | 108 / 116 / 124 | 93 / 139 | 0.275 / 0.6 → +0.325 | 0.35 |
| SOIC lead (0.6x1.6) | **6** | toe row0: 2; heel row0: 2; toe row1: 2 | 102 / 110 / 119 | 96 / 124 | 0.48 / 0.6 → +0.12 | 0.67 |
| QFN pad 0.5p (0.25x0.7) | **1** | toe row0: 1 | 95 / 103 / 111 | 25 / 181 | 0.28 / 0.35 → +0.07 | 0.25 |

Toe length needed (Ø0.25): 0.35 mm for one row, 0.60 for two, **0.85 for three** (0.02 gap + rows x 0.25 + 0.05 placement tolerance + 0.03 margin). No ball overhangs its pad sideways (all pads ≥ 0.25 wide).

## 1206: third toe row
- 14 balls = rows of 6 + 6 + 2 → **100 % at 15 µm** (91-108 % over 10-20 µm). The old 2-row layout (12 balls) was 89 %.
- Toe length for 3 rows: **0.85 mm** needed. The current 1206 pad (1.6 x 1.6, terminal covers 45 %) already exposes **0.88 mm**, so the 3rd row fits with **0.03 mm to spare and no extension**: pad stays 1.60 mm long. Optional: extend the toe by +0.05 (pad 1.65 mm, 0.93 exposed) for more placement margin; test both on the coupon.
- Row 2 sits ~0.55-0.80 mm from the terminal end (> 2 D); check on the coupon that it merges into the fillet and does not stay as a loose ball. If it does not merge, try 12 balls (89 %) with +1 tin step, or 13.

## Tunable ball count and the adjustment rule
Per part, `BALLS_OVERRIDE` in calc_v5.py. After each coupon round:
- **+1 ball** if the fillet is starved (concave below the termination's half height, or not wetted up the termination end).
- **-1 ball** if bridging, loose solder balls, or an over-full convex fillet.
- One step per coupon round; same change on both terminals; record the result. Each step is exactly 0.00818 mm³.

## Design note: dispensing / hot-air tips (pt1198u, 2026-10-29)
- All stations use all-metal Luer-lock tips (metal hub + 304 SS shaft), 1/2 in standard length. Plastic hubs are not used because of reflow heat. The hot-air reflow station also uses a Luer needle so its gauge can be changed if testing shows a gauge change helps.
- The current v4 head (linear_cam_short_v4) has no hot-air nozzle station (the v2 head had station E). The hot-air Luer needle applies when that station is added back; none is modelled yet.

## FLAGS
- **0402**: 2 balls = 108-124 %; needs a **+0.02 mm** toe extension (0.33 vs 0.35).
- **0603**: 4 balls in 2 rows (3 + 1) = 92-109 %; needs a **+0.105 mm** toe extension. Without it, use 3 balls in one row (82 % at 15 µm) and let the coupon decide.
- **SOT-23**: heel has only 0.275 exposed (< 0.35), so all 4 balls go on the toe in 2 rows: needs a **+0.325 mm** toe extension. Largest footprint change; check against the neighbour pads and the body outline.
- **SOIC**: 6 balls = 2 + 2 on the toe + 2 at the heel, 102-119 %; the second toe row needs a **+0.12 mm** toe extension. Without it: 4 balls (toe 2 + heel 2, 96 % at 15 µm).
- **QFN 0.5p**: 1 ball = 95-111 % (was 151-168 % with Ø0.30). The ball equals the 0.25 pad width, so no side overhang: **0.25 mm** to the next pad. Needs a **+0.07 mm** toe extension. The Ø0.30 QFN fallbacks are withdrawn.
- **0805, 1206**: fit without footprint changes.
- Keep ≥ 0.20 mm pad-to-pad around toes that carry balls, including the extensions.

## Coupon tests (TODO 17) - these set the final values
17. [ ] Coupon for every part (0402, 0603, 0805, 1206, SOT-23, SOIC, QFN), on ENIG and on laser-opened copper, all with Ø0.25 balls:
    - **Tin flatness:** per-pad tin 10-20 µm, peak ≤ 25 µm, pads of one part within 10 µm.
    - **Ball count:** baseline, -1 and +1 side by side; apply the adjustment rule.
    - **1206 3rd row:** 14 balls on the 1.60 pad and on a 1.65 pad; does row 2 merge?
    - **Bridging:** 0402 at 0.20 mm pad spacing and QFN 0.5 pitch, with and without the toe extension.
    - Toe extensions: 0402 +0.02, 0603 +0.105, SOT-23 +0.325, SOIC +0.12, QFN +0.07 vs the current footprints.
    - 0402 tilt and tombstones, ball merge into the fillet, wetting on laser-opened copper, fillet height.
