# OSSO PCB rules
Added 2026-10-28 (consistency review A11, approved by the designer).

## Pogo pads and vias
1. Every pogo pad is tied into the copper pour with zero clearance. This is how circuits reach the board interior and the adjacent boards through the interposer.
2. A pogo pad never gets a via of its own (no via-in-pad, no dedicated via next to it), because the pad's net on the bottom need not match the pad on the top.
3. When a top pad and a bottom pad must connect, route each through the engraved pour to an EXISTING via of the fixed via grid.
4. Only the fiducials are isolated in the factory copper. All other isolation is made by laser engraving the pour.
5. Fab check (to add to check_frameless_r1.py / check_v3c.py): fail if any PTH via centre lies within (pogo pad R + via pad R + 0.15) of a pogo pad centre.

## Related, confirmed 2026-10-28
- Interposer snap: the barb seat keeps its solder mask. Check the snap Ø5.0 copper-free void to the nearest pogo PAD edge ≥ 0.3 (there is no pogo isolation ring).
- Tooling: Ø3.0 non-plated hole at (70,4) and a 2.0x3.0 non-plated slot at (70,136), long axis Y (v1n = v3c).
- Fiducials A (22,4), B (118,4) Ø0.4 plated; C (118,136) top / C' (22,136) bottom.
- Vias: Ø0.3 drill / Ø0.6 pad, tented.
- Clamp only in the 4 jig clamp zones (project/pcb/fab/v3c_blank/JIG_HOLD.md); never on ENIG.

## Job QR patch (PR-QR, added 2026-11-02, run 25 / JQR-01)
6. Every job PCB carries a job QR patch on BOTH sides, mirrored, at board X 66-74, Y 9-17 (8x8, on the flip axis x = 70, so top and bottom occupy the same board XY). This is the fiducial-free spot at the near edge closest to the angled crosshair camera.
7. Keep 1.0 clear of the patch: no vias, pogo pads, fiducials, tooling hole or clamp zones. Checked against v3c: edge vias y 7.5 (gap 64.92/75.08), via grid starts y 14.12 (none near x 70), tooling hole (70,4), fiducials A (22,4) and B (118,4), clamp zones Z1/Z2 x 27-63 / 77-113 y 1-6, power corners.
8. No custom stencils or per-job masks, ever (SR-033).

## Companion boards (PR-CB, added 2026-11-03, run 31 / SR-053)
9. A companion board that the machine places with N8 (fixed 6-8 mm soft silicone cup) must weigh 50 g or less and carry a flat, bare PnP target at its centre of mass: a 10 mm diameter circle minimum (12 mm preferred), no parts, vias, text or solder mask openings inside it, with a silkscreen outline and the label "PnP" next to it.
10. N8 hold check: 7 mm cup at -70 kPa gives about 2.7 N theoretical (about 1.3 N at a 50 % seal factor) against 0.49 N for a 50 g board: SF about 2.7 with the seal factor, at the head accelerations used for picks. Heavier boards, boards without the target, or a target outside N8 reach (PCB X 263-390) are placed by hand.

## Volume refactor (PR-VR, added 2026-11-04, run 35 / SR-058)
11. A fully tested OSSO PCB with its interposer stack can be refactored by the OSSO software into a single multi-layer PCB, with new sizing and port (connector) locations, for volume manufacturing by a fab. This refactored multi-layer PCB is the final destination of the OSSO prototyping workflow: it is sized and its ports placed to meet the packaging constraints of the final product. Design intent only; no CAD change in run 35.
