# OSSO interposer assembly jig v1 (item 6, run q_run_20261028)
For cad/interposer/frameless_r5a. Three custom FDM parts (PETG, 0.2 layer, 4 walls, 40% gyroid) + 2 dowel pins (Ø3 h7x40, Ø2 h7x40, press-fit in the base; ream to fit).

Steps (see OSSO_interposer_jig_v1_load_insert.mp4 / .usdz):
1. Put the interposer upside down in the nest (top face on the nest floor z 9.0; pocket = outline +0.15).
2. Place the loading mask on the dowels. It rests on the interposer PCB face and has Ø2.4→Ø3.5 funnels over the 40 counterbores and Ø7.5 windows around the clips.
3. Drop the 40 YZD0029 pins collar-up (barrel through the Ø1.65 guide; collar on the counterbore floor). The lower tips go into Ø1.5 relief holes (tip z 7.2, floor z 5.0).
4. Lift off the mask.
5. Lower the PCB onto the dowels (tooling hole Ø3 at (70,4), 2x3 slot at (70,136)). It rests on the clip barb ramps at z 23.32.
6–7. Lower the press plate onto the dowels and push it down 2.52 mm. The Ø9/Ø6 rings around each drill and the 4 clamp-zone pushers drive the PCB straight down, and the clips snap. A hard stop comes from the PCB seating on the 4 clamp-zone pads and the interposer face (z 20.8). The clip-tip relief in the press leaves 4.9 mm of clearance.
8–9. Lift the press, then lift the assembly out and flip it.

There is no pin preload during the snap: the PCB-side plungers sit 0.1 below the PCB face. Insertion force is clips only (estimated, not measured).
Checks: jig_checks_geom.json, jig_checks_interference.json. The seated state has no clashes except the intended 0.05 dowel press-fit, and there are 0 pin overlaps.
Files: OSSO_interposer_jig_v1.step (top-level components/custom_parts/panels; panels holds a placeholder only because this jig has no panels), .glb (front view), *_base/_mask/_press.stl, drawing PNG, MP4/USDZ, anim_step*.png.
Scripts: make_jig.py → export_jig.py → anim_jig.py → make_drawing.py.
Assumption: the PCB REF is a plain 140x140 with the tooling hole, slot and 4 Ø3 drills. Before printing, check the v1n parts on the opposite face for keep-outs against the press pushers (clamp zones + Ø9 rings only).

## 2026-10-28: pressed BY HAND (the designer)
- The press plate is kept. Added ergonomics: two finger-grip ears on the X sides (each 26 x 18 out x 5 thick, flush with the top, R4 corners, 3 cross grooves 1 x 0.8 for grip), plus the existing 2-deep palm recess. Lift and place with the ears, push with the palm on the recess. The base finger notches stay.
- Snap force (snap_force.py, jig_snap_force.json): 8 tines (4 clips x 2), beam 5.65, t 0.9, deflection 0.4, 30° ramp, μ 0.3 → **~11 N (tough resin) to ~17 N (standard resin) total peak**. That is well below a comfortable palm push (50-150 N) and even a thumb press, so it is fine by hand. There is no pogo preload during the snap. Use tough resin for the clips (1.69 % strain).
- STL/STEP re-exported. The drawing does not show the ears (top view note only); press STL is the reference.
- The seated base-dowel overlaps (d3 1.87, d2 1.24 mm³) are the intended press fits.
